There are 13 standard carbide burr shapes, coded SA through SN. The letter is the shape; Most buyers who order the wrong burr have the material and the cut figured out. The problem is reach: they pick a profile that can't physically get at the surface. An SA where the job needs an end cut, a ball where a fillet was needed, a flame where the corner has to be square.
This chart covers all 13 profiles: what each one reaches and where each one fails. If you already know your shape code and just need speed data, head to the carbide burr RPM chart instead.
![]()
The 13-shape system is set out in ISO 7755 (hardmetal burrs), and the same SA–SN letters turn up in North American and European catalogues alike. Every burr we supply follows this coding, so a shape code on your purchase order will match what arrives.
Two things about the code trip up first-time buyers.
First, the letter is the shape, the number is the size. SA-1 through SA-9 are nine sizes of one shape. A catalogue listing "SA-1, SA-2, SA-3…" isn't offering nine shapes, just nine diameters and lengths of the same cylinder. And the number doesn't run on a universal scale. SA-5 and SD-5 are both "size 5" within their own families, but the two heads aren't the same dimension.
Second, similar-looking codes are genuinely different tools. SA, SB and SC are all cylinders. In use they behave nothing alike. The difference is entirely at the end of the head.
We can cross-reference DIN to ANSI on request. Send the drawing and we'll confirm the equivalent before you order.
| Code | Shape | What the end looks like | Best used for | Where it fails |
| SA | Cylindrical, no end cut | Flat top, no teeth on the top | Straight edges, weld dressing on plate, finishing slot walls | Cannot plunge — the flat face rubs and burnishes instead of cutting |
| SB | Cylindrical, with end cut | Flat top with cutting teeth | Plunge cutting, squaring a corner, opening and enlarging holes, spot facing | Plunge cutting, squaring a corner, opening and enlarging holes, spot facing |
| SC | Cylindrical, radius end | Rounded corner on a cylindrical body | Rounded corner on a cylindrical body | Tilting the tool leaves a visible step at the radius |
| SD | Ball | Full sphere | Contoured surfaces, radii, hollowing, deburring inside curves | Small contact patch — wears fast if you lean on it |
| SE | Oval (egg) | Elliptical | Soft contours, blending on curved castings, aluminium and brass | Will not sit flat; poor choice for flat-bottom work |
|
SF |
Tree, radius end | Tapered body, rounded top | Bottom of deep pockets, internal fillets, cavity work | Long reach invites chatter — keep overhang short |
|
SG |
Tree, point end | Tapered body, pointed top | Starting a hole, chamfering, tight internal corners, opening narrow slots | The point is the weakest section; avoid side loading |
| SH | Flame | Flame profile | General deburring, weld seams, mixed contours — the best single-burr compromise | Good at many jobs, best at none |
| SJ | Cone, 60°, radius | 60° included angle | Chamfering, deburring hole edges, 60° seat preparation | Angle must match the print or the seat will not seal |
| SK | Cone, 90°, radius | 90° included angle | Chamfering, countersink preparation, edge breaking | Same — verify the angle before ordering |
| SL | Taper, radius end | Long taper with rounded tip | Tapered slots, dovetail forms, narrow angled recesses | A slightly bent shank makes a taper run out immediately |
| SM | Cone, point end | Sharp-pointed cone | Deburring small holes, fine detail, scribing | Tip is very fragile; unsuitable for heavy stock removal |
| SN | Inverted cone | Cone with the tip inverted | Back deburring, chamfering the far side of a through hole, T-slots | Needs clearance behind the workpiece |
Five profiles cover most of our catalogue: SA, SB, SC, SG and SL. That's what die, mould, weld and fabrication work actually asks for. All 13 are available to order;
Shape selection should start from the surface, not from the catalogue. Work backwards from what you need to reach:
| Your task | Start with | Why this one |
| Deburring a straight edge or weld seam | Flat side wall presents the most teeth to a straight edge | |
| Enlarging or opening a hole | Both cut on the end, so they can feed axially | |
| Blending a fillet into a flat face |
SC, SD |
Radius matches the fillet without undercutting the face |
| Hollowing a curved surface |
SD, SE |
Spherical and elliptical profiles follow curvature in any direction |
| Cleaning the bottom of a deep pocket | Tapered body reaches past the walls without rubbing them | |
| Back chamfering a through hole |
SN |
Only profile designed to cut on the far side |
| Chamfering a hole edge |
SJ, SK |
Fixed included angle gives a repeatable chamfer |
| One burr for mixed general work | Flame profile is the accepted general-purpose compromise |
The shape decides where the burr can reach; the cut decides how it behaves once it's there. Specify one without the other and you get a tool that fits the job but finishes badly.
Tooth geometry and flute count change how aggressively a given shape cuts, whichever cut you choose. That's covered separately in how carbide burr tooth geometry affects cutting performance.
For an accurate quote we need five things: shape code and size (SA-5, for example), head diameter × length, shank diameter, cut type and quantity. If all you have is a drawing or a sample, send either. We'll identify the profile and confirm the equivalent code before production.
If you'd rather have a stocked assortment than individual sizes, carbide burr sets put the common shapes in one case. That's usually the cheaper way to work out which profiles your work actually needs.
Not sure which profile you need? Tell us the material, the feature you're deburring or blending, and the tool you're running it in. We'll recommend a shape, a cut and a starting RPM. If no standard profile will reach the feature, we can make a custom head to your drawing.
What do the letters SA, SB and SC mean on a carbide burr?
They're shape codes from ISO 7755, used in North American and European catalogues alike. SA is a cylinder with no end cut, SB is the same cylinder with an end cut, and SC has a radius end. The letter defines the profile; the number defines the size within it.
What is the difference between SA and SB burrs?
Only the end. SA has a plain flat face with no cutting teeth, so it works on side walls but can't be plunged. SB has teeth across the end face, so you can feed it straight into the work to open holes or square corners.
How many standard carbide burr shapes are there?
Thirteen: SA, SB, SC, SD, SE, SF, SG, SH, SJ, SK, SL, SM and SN. Custom and modified profiles exist too, but those thirteen cover almost all standard deburring, blending and stock removal work.
Can I use a 6 mm shank burr in a 1/4" die grinder?
Only if the collet is genuinely 6 mm. 1/4" is 6.35 mm, so a 6 mm shank sits loose in a 1/4" collet and slips under load. A 1/4" shank won't fit a 6 mm collet at all. Check the marking on the collet instead of assuming.
Single cut or double cut for stainless steel?
Double cut. The cross-hatch pattern breaks chips small, cuts more smoothly and gives better control in work-hardening alloys. For aluminium, brass and soft steel, single cut is better when fast stock removal and chip clearance matter more than finish.
Which burr shape is best for general deburring?
There is no single "best" shape for every job, because the right burr depends on the edge or contour you are cleaning. However, a few shapes cover most general deburring tasks: SA-5, SC-5, SF-5, SG-5